Ingersoll Rand Gravity Feed Spray Gun 210g
47083068
Edition 1 December 2009
Paint Sprayer
Models 200G, 210G, 270G and 210CSA
Product Information
EN Product Information
ES Especificaciones del producto
FR Spécifications du produit
Save These Instructions
MODEL 210CSA
2
1
3
(Dwg. 47083233)
(Dwg. TP2051)
MODEL 200G, 210G and 270G
1
2
3 
2 
1
| 3 | ||
| 5 | 7 | 48h |
| 6 | 4 |
(Dwg. 16577629)
| 4 | 5 |
| inch (mm) | NPS (inch) |
| 5/16 (8) | 1/4 |
47083068_ed1
EN
Product Safety Information
Intended Use:
Paint Sprayers are designed for paint, lacquer, stain or other finish type material.
For additional information refer to Product Safety Information Manual Form 16576563.
Manuals can be downloaded from www.ingersollrandproducts.com.
Product Specifications
| Model | Description | Maximum | Average Air | Tool | Cup | Fluid | |
| Air Pressure | Consumption | Weight | Capacity | Nozzle Size | |||
| 200G | Touch-Up Gravity | 35 psig | 5 cfm | 1.2 lbs | 4.2 oz | 0.03 in | |
| Feed Spray Gun | [2.4 bar] | [140 l/min] | [0.52 kg] | [125 cc] | [0.8 mm] | ||
| 210G | Gravity Feed | 60 psig | 11 cfm | 2.6 lbs | 20 oz | 0.05 in | |
| Spray Gun | [4.1 bar] | [300 l/min] | [1.2 kg] | [600 cc] | [1.4 mm] | ||
| 270G | HVLP Gravity | 40 psig | 8 cfm | 2.7 lbs | 33 oz | 0.06 in | |
| Feed Spray Gun | [2.8 bar] | [235 l/min] | [1.3 kg] | [1,000 cc] | [1.5 mm] | ||
| 210CSA | Suction Feed | 60 psig | 12 cfm | 1.5 lbs | 33 oz | 0.07 in | |
| Spray Gun | [4.1 bar] | [340 l/min] | [0.62 kg] | [1,000 cc] | [1.8 mm] | ||
Operations
Spray Gun Handling
WARNING
Do not point the spray gun at anyone or at any part of the body.
NOTICE
Ensure appropriate air line filter is being used. Water, oil, and debris in the air may cause damage to the workpiece.
The spray gun should be held perpendicular to the work surface and 6 to 12 inches from the work surface. Keep the gun parallel to the work surface during the stroke to ensure even coating. DO NOT move the gun in an arc. This will result in a build up of paint in the center of the stroke and a light coating at each end.
Start the gun moving prior to pulling the trigger and release the trigger before stopping the gun movement. Overlap strokes enough to get a uniform finish.
Fan Direction
Air Cap
Lock Ring
| (Dwg. TP2049) | (Dwg. TP2053) |
| 47083068_ed1 | EN- |
EN
WARNING
Always turn off the air supply and disconnect the air supply hose before installing, removing or adjusting any accessory on this tool, or before performing any maintenance on this tool.
The direction of the fan can be adjusted from horizontal to vertical be loosening the lock ring and turning the air cap to the proper location. Hand tighten lock ring after adjustment.
Controls
Refer to illustration 47083233 on page 2.
1. Fluid Control
The fluid control knob will adjust the atomization of the paint. Turn the knob clockwise until fully closed. Then while turning the knob
counterclockwise, trigger short bursts of paint. This counterclockwise movement of the knob will move the pattern from fine to coarse. Adjust the knob until the desired pattern is obtained.
2. Pattern Control
The pattern control knob adjusts the size of the fan. A wide fan will result if the knob is fully opened by turning it counterclockwise. As the knob is turned clockwise, a smaller round pattern will be achieved.
3. Air Control (If Applicable)
Open the air control knob fully by turning counter clockwise. Set desired air pressure using regulator. Do not exceed maximum air pressure. If a lower air pressure is desired for some parts of the spray job, turn the air control knob clockwise as needed.
Spray Patterns
If the pattern is too coarse and the fluid control knob can not adjust it properly, try adjusting the air pressure or thin the paint to achieve
desired pattern.
The spray pattern varies from round to flat with patterns in between (Refer to illustration TP2051 on Page 2).
Routine Maintenance
NOTICE
Dispose of hazardous fluid according to all local, state, and national guidelines.
WARNING
Always turn off the air supply and disconnect the air supply hose before installing, removing or adjusting any accessory on this tool, or before performing any maintenance on this tool.
Clean spray gun and canisters immediately after use. Paint or other fluids can dry quickly and can easily plug internal passageways and render the spray gun useless.
WARNING
Do not use Methylene chloride (Dichloromethane) or any halogenated hydrocarbon solvents with this spray gun.
EN
Remove and empty the canister. Rinse canister with a solvent recommended for the paint being used.
Fill canister with solvent and attach to spray gun. Spray solvent into an approved container, while shaking the gun vigorously. Continue until all traces of paint have been eliminated from spray. Also wipe the exterior of the gun with a rag soaked with the solvent.
Remove the air cap and soak in solvent. Use a toothpick or plastic brush, to clean air passages.
NOTICE
Using metal objects can damage the precision air passages. DO NOT soak spray gun in solvent. This can damage non-metallic
components.
NOTICE
After cleaning, lubricate lightly with NON-SILICONE OIL. Silicone oil can cause oil spots to occur in the paint.
Installation and Lubrication
Size air supply line to ensure tool's maximum operating pressure (PMAX) at tool inlet. Drain condensate from valve(s) at low point(s) of piping, air filter and compressor tank daily. Install a properly sized Safety Air Fuse upstream of hose and use an anti-whip device across any hose coupling without internal shut-off, to prevent hose whipping if a hose fails or coupling disconnects. See drawing 16577629 and table on page 2. Maintenance frequency is shown in circular arrow and defined as h=hours, d=days, and m=months of actual use.. Items identified as:
| 1. | Air filter | 5. | Thread size |
| 2. | Regulator | 6. | Coupling |
| 3. | Emergency shut-off valve | 7. | Safety Air Fuse |
4. Hose diameter
Parts and Maintenance
When the life of the tool has expired, it is recommended that the tool be disassembled, degreased and parts be separated by material so that they can be recycled.
The original language of this manual is English.
Tool repair and maintenance should only be carried out by an authorized Service Center. Refer all communications to the nearest Ingersoll Rand Office or Distributor.
Source: https://manualmachine.com/ingersollrand/210csa/1282481-user-manual/
0 Response to "Ingersoll Rand Gravity Feed Spray Gun 210g"
Post a Comment